What Is Auto Immobolizer System?

Car theft system refers to the system that prevents the car itself or the items on the car from being stolen. It consists of electronically controlled remote control or key, electronic control circuit,CGDI Prog alarm device and the implementation of institutions and other components.  

The earliest car door lock is a mechanical door lock, only for car driving to prevent the door automatically open and accident, only the safety of traffic, can not afford the anti-theft effect. With the progress of society, the development of science and technology  SKP1000 Programmer and the increasing number of cars, and later the manufacture of cars, trucks doors are equipped with a key lock. The door locks only one door, and the other door is opened or locked by the door lock on the door VVDI Key Tool

In order to better play the role of anti-theft, and some cars also equipped with a steering lock. The steering lock is used to lock the steering wheel of the car. The steering lock is locked with the ignition and is installed under the steering wheel, which is controlled by the key X431.

 That is, the ignition lock cut off the ignition circuit to turn off the engine, the ignition key and then left to the extreme position of the gear, the latch will be extended into the steering shaft slot, the car steering shaft mechanical lock. Even if someone will open the door and start the engine illegally, because the steering wheel is locked, the car can not be turned, it can not drive away, so played a car anti-theft effect Fcar F3-G. 

 Some cars are designed and manufactured without a steering lock, but with another so-called crutches lock the steering wheel, so that the steering wheel can not turn, but also can play an anti-theft effect. Some cars in the transmission with a mechanical lock, the transmission lever is locked, so that the theft can not be linked to the car can not move. Ignition switch is used to turn on or off the engine ignition system circuit, according to a key to open a lock of the truth, but also played a certain anti-theft effect. As the car technology continues to develop, most cars are installed on the central door locks, that is, the car door locks and luggage compartment lock to achieve centralized control.

Magenta Pump Leakage Coolant Failure Case

Vehicle Information
Model: MAGOTAN 1.8T

Symptom:

MAGOTAN 1.8T new car more than 4,000 kilometers of water pump leakage of coolant, replace the pump after driving more than 1,000 kilometers, the pump once again leak antifreeze.Launch X431 Tool


Fault analysis and maintenance process Vpecker E4
1. When the vehicle travels 4011km, the station checks the leakage antifreeze. After checking the water tank, it leaks the antifreeze, removes the water pump and finds that the temperature inside the side outlet of the thermostat is damaged.Fcar F502
2. Replace the pump after the vehicle and travel about 1000km, once again complained about the antifreeze and leakage, check or water leakage at the pump antifreeze. Remove the pump to find the pump or in the side of the thermostat side of the outlet is damaged, the damage is the same as the first, (as shown below)
Professional DPF+EGR Remover 3.0
3. Because this vehicle is a new car and the damage location of the two pumps is roughly the same, analysis and pump quality problems caused by the probability is not that there should be other aspects of the problem, resulting in a series of damage to the pump.OBDSTAR TP50


On the form of damage to the pump, there are several possibilities:


1, the quality of the pump itself is a problem
2, the installation location of the pump problem
3, the installation of the pump cylinder surface protruding
4, there are external forces lead
4 because the water has been continuously damaged two pumps, analysis of the pump itself is unlikely to cause the problem; the new pump smear sealant, check the location of the pump installation; the engine block and the pump surface of the flatness of the inspection, Check the flatness normal.

5. In the process of inspection SBB Key Programmer found in the 2-cylinder, 3-cylinder injector at the bottom of a large number of yellow gasoline residue traces (as shown below), combined with the customer response sometimes in the cab can smell the smell of gasoline. Analysis of the traces should be leaking out of the gasoline traces, but the leakage of gasoline and water pump damage is it?



6. Further inspection VVDI found that the pump seal some swelling (see below), originally thought that the pump shell damage after the shell elongated, and now look at the petrol bedroom seal, resulting in swelling, and thus bulging the shell Body, causing leakage.


7. From the oil point of view 2 cylinder 3 cylinder position traces of gasoline traces more serious, remove the 2 cylinder, 3 cylinder nozzle, can be observed in the 3-cylinder fuel injector plug with gasoline, the surface of the gasoline flow trace. To determine the fault is caused by the 2-cylinder, 3-cylinder injector oil spill. The results replaced the 2-cylinder, 3-cylinder injector, and replaced the 1-cylinder, 4-cylinder nozzle seal.

8. After the vehicle is shipped, it is tracked, the next day the customer feedback feels good. And after a few days of customer feedback, in the cab and smell the smell of gasoline. Immediately about customers to check.skp900 programmer

9. Vehicles came to the service station, open the engine compartment, you can smell the smell of gasoline. Because the car's fuel injector installed in the lower part of the inlet, the eyes can not look directly to, in order to be able to accurately find the leakage point, learn the first two training lessons, in no hurry to disassemble and repair. The engine was in a state of fire, carefully observed in the bottom of the 4-cylinder injector formed gasoline droplets, check found in the top of the 4-cylinder injector, from the rails to leaking gasoline.


10. After removing the rails, observe that the guide rail has a vertical groove at the installation of the 4-cylinder injector. Sealed the place, put the rails up, into the gasoline, after a period of time, can be observed from the vertical at the vertical leakage of gasoline. (Pictured)


Failure analysis:

Because the 4-cylinder fuel rails have cracks, resulting in gasoline leakage, leaking out of the gasoline gradually immersed in the pump seal, the ring erosion swelling, resulting in damage to the pump, leakage antifreeze,


Troubleshooting:

Replacement of oil rails and pumps


Special tools / equipment: T10133 torque wrench VAS6150B OBD2


Maintenance Summary:

Water pump leakage is a more common fault, but the new car in the short term continuous damage we first met. The second maintenance, although checked out of the gasoline leak, led to the pump seal inflated, but did not find the root cause of the problem. On the one hand is the main location of the fuel injector installed in the lower part of the inlet, the naked eye can not be observed; the other hand, our inspection work is not enough detail. Need to sum up lessons learned. Do a good job of technical work, to study the investigation, root cause.